CUMMINS N14 Especificaciones Pagina 237
- Pagina / 587
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Caution: Wear protective gloves when handling parts
that have been heated to prevent personal injury.
Heat the gear in an oven at 260°C [500°F] for a minimum
of 1 hour.
Remove the gear from the oven.
NOTE: Install the gear on the camshaft within 30 seconds
after it is removed from the oven.
Caution: The timing marks and the part number on the
gear must be facing away from the camshaft when the
gear is installed to prevent engine damage.
Align the gear keyway with the key in the camshaft, and
install the gear.
NOTE: Keep the camshaft in a vertical position with the gear
up until the gear has cooled.
Caution: Do not use water or oil to reduce the cooling
time. The gear can crack. Allow the air to cool the gear.
If the gear does not seat against the locating shoulder on
the camshaft, remove the gear and install it again.
Use a feeler gauge to check the clearance between the
camshaft gear and the shoulder. The clearance must not
exceed 0.13 mm [0.005-inch].
Gear Cover - Cleaning and Inspection
(01-19)
Cleaning
Use a mallet and a mandrel or a drift to remove the front
crankshaft seal and the accessory drive seal.
Cylinder Block Gear Cover - Cleaning and Inspection (01-19)
N14 Page 1-69
- Foreword 2
- TABLE OF CONTENTS 3
- Section I - Introduction 5
- Manual Organization 6
- General Repair Instructions 7
- General Safety Instructions 8
- Symbols Used in this Manual 9
- Illustrations 13
- Glossary Of Terms 14
- Engine Identification 16
- Engine Diagrams 17
- N14Page i-14 18
- N14 Page i-15 19
- General Cleaning Instructions 20
- Engine Disassembly (00-01) 30
- Coolant - Drainage 31
- Coolant Filter - Removal 31
- Crankcase Breather - Removal 32
- Turbocharger - Removal 32
- Exhaust Manifold - Removal 33
- Starting Motor - Removal 33
- Fan and Fan Spacer - Removal 33
- Alternator Belts - Removal 33
- Alternator - Removal 34
- Water Header Covers - Removal 36
- Flywheel - Removal 38
- Flywheel Housing - Removal 39
- Rear Cover - Removal 40
- Fan Belts - Removal 40
- - Removal 41
- Water Pump Belt - Removal 41
- Thermostat Housing - Removal 42
- Outlet Tubes - Removal 42
- Water Pump - Removal 43
- Vibration Damper - Removal 43
- (ECM) - Removal 48
- CELECT™ Ambient Air Pressure 48
- Sensor - Removal 48
- Fuel Pump - Removal 49
- Air Compressor - Removal 50
- Viscosity Sensor - Removal 52
- Intake Manifold - Removal 53
- Engine Brakes - Removal 54
- Valve Crossheads - Removal 55
- Push Tubes - Removal 55
- Injectors - Removal 55
- Fuel Crossovers - Removal 57
- Cylinder Heads - Removal 57
- Lubricating Oil Pan - Removal 59
- Gear Cover - Removal 59
- Camshaft - Removal 59
- Cylinder Liners - Removal 62
- Crankshaft - Removal 64
- Engine Assembly (00-02) 66
- Crankshaft - Installation 68
- Rear Cover - Installation 85
- Bore Alignment - Measurement 88
- Face Alignment - Measurement 90
- Flywheel - Installation 92
- Cylinder Heads - Installation 96
- Camshaft - Installation 98
- Timing Tool Installation 102
- (EPS) - Installation 111
- Gear Cover - Installation 112
- Injectors - Installation 120
- STC Engines 121
- Push Tubes - Installation 122
- Installation 124
- Injector and Valve Adjustment 125
- Engine Brake - Installation 135
- Engine Brake - Adjustment 135
- C-Brake - Alternate Method 138
- Jacobs Brake 139
- Sensor - Installation 141
- Fuel Tubing - Installation 143
- Air Compressor - Installation 144
- Fuel Pump - Installation 144
- Water Pump - Installation 153
- Adjustment 154
- - Installation 155
- Outlet Tubes - Installation 155
- Alternator - Installation 162
- Starting Motor - Installation 164
- Turbocharger - Installation 165
- Coolant Filter - Installation 167
- Section Contents 169
- N14Page 1-6 174
- Dowel Pin - Removal 178
- Camshaft Bushings - Removal 179
- Cylinder Block - Cleaning 179
- Camshaft Bore - Cleaning 183
- Camshaft Bore - Inspection 183
- Cylinder Block - Inspection 188
- Coolant Passage - Inspection 189
- Coolant Passage - Repairing 191
- Dowel Pin - Installation 202
- Cleaning 204
- Inspection 206
- Inspection (01-09) 215
- Alignment - Inspection 216
- Twist - Inspection 217
- Inspection (01-11) 219
- Inspection (01-12) 220
- Inspection (01-13) 221
- Inspection (01-16) 230
- Thrust Bearings - Inspection 231
- Cylinder Head - Service Tools 244
- Cylinder Head - Exploded View 248
- Disassembly 252
- Grinding the Valve Seats 259
- Assembly 263
- Guides (02-03) 267
- Seat Inserts (02-05) 269
- Sleeves (02-07) 273
- Checking (02-09) 279
- Seating for Reuse (02-10) 280
- Crack Inspection (02-11) 282
- Checking for Reuse (02-12) 283
- Inspection (02-13) 284
- N14Page 3-4 288
- Cleaning and Inspection 292
- Rocker Lever - Magnetic Crack 298
- Inspection (03-03) 298
- Inspection for Reuse (03-04) 298
- Water Manifold Tube - Removal 299
- Inspection for Reuse (03-06) 303
- Replacement (03-08) 305
- Inspection - Magnetic Crack 319
- Inspection - Dimensional 319
- Cleaning - PT Fuel Pump 328
- Cleaning - CELECT™ Fuel Pump 329
- Inspection - PT Fuel Pump 329
- Fuel Pump - Rebuild (05-02) 332
- Inspection for Reuse (06-01) 339
- Inspection - CELECT™ 340
- Injectors - Rebuild (06-02) 341
- Reuse (06-05) 342
- Inspection for Reuse (07-01) 350
- Inspection for Reuse (07-05) 352
- Bushing - Replacement (07-07) 361
- Bushing - Replacement (07-08) 367
- Shaft - Replacement (07-09) 368
- Replacement (07-10) 369
- Rebuild (07-11) 370
- Testing - Oil Cooler Core 375
- Poppet Valve Spring 377
- Inspection (08-01) 386
- Water Pump Assembly - Rebuild 387
- Inspection (08-05) 399
- Inspection (08-09) 404
- Drive Units - Service Tools 406
- Accessory Drive 408
- Inspection for Reuse (09-01) 409
- Inspection for Reuse (09-04) 417
- Replacement (09-05) 417
- Checking (10-02) 426
- - Checking (10-03) 426
- Inspection for Reuse (11-01) 431
- Exhaust Manifold Turbocharger 432
- Air Compressor 434
- Air Compressor - Cleaning and 435
- Inspection for Reuse (12-01) 435
- General Information 442
- Cummins 1991 N14 Heavy Duty 443
- Engine Operating Curve 443
- Definitions: 443
- General Run-In Procedures 444
- Fuel Rate 452
- Fuel Inlet Restriction 452
- Fuel Pressure 453
- Fuel Drain Line Restriction 453
- Systems (14-02) 458
- Dynamometer (14-03) 464
- Dynamometer Worksheet 468
- Chassis Dynamometer Operation 469
- Dynamometer (14-05) 471
- Intake Manifold Pressure 474
- Charge Air Cooler Restriction 475
- Intake Air Restriction 475
- Exhaust Air Restriction 476
- Engine Blowby 476
- Lubricating Oil Pressure 477
- Coolant Pressure 477
- Dynamometer (14-06) 478
- Dynamometer (14-07) 481
- Engine Painting (14-08) 482
- Air Heaters 490
- Coolant Heaters 490
- Engine Protection Controls 490
- Fuel Warmers 490
- Oil Heaters 491
- Reuse (16-01) 496
- Inspection for Reuse (16-03) 497
- Flywheel Housing - Redowel to 498
- Cylinder Block (16-04) 498
- Specifications - Group 18 505
- General Engine Specifications 507
- Exhaust System 508
- Fuel System 508
- Electrical System 508
- Pipe Plug Torque Values 510
- NT 855 Page 18-9 513
- Page 18-10 NT 855 514
- NT 855 Page 18-11 515
- Page 18-12 NT 855 516
- NT 855 Page 18-13 517
- Page 18-14 NT 855 518
- NT 855 Page 18-15 519
- Page 18-16 NT 855 520
- NT 855 Page 18-17 521
- Page 18-18 NT 855 522
- NT 855 Page 18-19 523
- Page 18-20 NT 855 524
- NT 855 Page 18-21 525
- Page 18-22 NT 855 526
- NT 855 Page 18-23 527
- Page 18-24 NT 855 528
- NT 855 Page 18-25 529
- Page 18-26 NT 855 530
- NT 855 Page 18-27 531
- Page 18-28 NT 855 532
- NT 855 Page 18-29 533
- Page 18-30 NT 855 534
- NT 855 Page 18-31 535
- Page 18-32 NT 855 536
- NT 855 Page 18-33 537
- Page 18-34 NT 855 538
- NT 855 Page 18-35 539
- Page 18-36 NT 855 540
- NT 855 Page 18-37 541
- Page 18-38 NT 855 542
- NT 855 Page 18-39 543
- Page 18-40 NT 855 544
- NT 855 Page 18-41 545
- Page 18-42 NT 855 546
- Cylinder Head - Torque Values 547
- Page 18-44 NT 855 548
- ST-1182 549
- NT 855 Page 18-45 549
- Fixed Injection Timing 550
- MVT Injection Timing 550
- NT 855 Page 18-47 551
- Page 18-48 NT 855 552
- NT 855 Page 18-49 553
- Page 18-50 NT 855 554
- NT 855 Page 18-51 555
- Page 18-52 NT 855 556
- NT 855 Page 18-53 557
- Page 18-54 NT 855 558
- NT 855 Page 18-55 559
- Page 18-56 NT 855 560
- NT 855 Page 18-57 561
- Page 18-58 NT 855 562
- NT 855 Page 18-59 563
- Page 18-60 NT 855 564
- NT 855 Page 18-61 565
- Cooling System -Torque Values 566
- NT 855 Page 18-63 567
- Page 18-64 NT 855 568
- NT 855 Page 18-65 569
- Page 18-66 NT 855 570
- NT 855 Page 18-67 571
- JacobsW Engine Brake 573
- Cummins C Brake 573
- Component Manufacturers 574
- N14Page C-2 575
- Torque Converters 576
- Additional Service Literature 578
- Order Total 580
- Page X-1 582
- Page X-2 583
- Page X-3 584
- Page X-4 585
- BUSINESS REPLY MAIL 586
- Literature Survey Form 587
Comentarios a estos manuales
Waters XBridge Protein BEH, C4, 300A, 3.5 µm Columns podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt wodny Waters XBridge Protein BEH, C4, 300A, 3.5 µm Columns.
Dostarczamy 1 pdf podręczników Waters XBridge Protein BEH, C4, 300A, 3.5 µm Columns do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Waters XBridge Protein BEH, C4, 300A, 3.5 µm Columns Instrukcja Użytkownika (11 strony)
Marka: Waters | Kategoria: Water equipment | Rozmiar: 1.43 MB |
Spis treści
Więcej produktów i instrukcji dla Sprzęt wodny Waters
| Modele | Rodzaj dokumentu |
|---|---|
| MassPREP Enolase Digest with Phosphopeptides Mix |
Instrukcja Użytkownika
Waters MassPREP Enolase Digest with Phosphopeptides Mix User Manual,
4 strony
|
| Protein-Pak Epoxy-Activated Affinity Products |
Instrukcja Użytkownika
Waters Protein-Pak Epoxy-Activated Affinity Products User Manual,
6 strony
|
| Porapak Gas Chromatography Column Packing Material |
Instrukcja Użytkownika
Waters Porapak Gas Chromatography Column Packing Materials User Manual,
3 strony
|
| Sep-Pak Cartridges and Plates |
Instrukcja Użytkownika
Waters Sep-Pak Cartridges and Plates User Manual,
6 strony
|
| High Performance Carbohydrate Column |
Instrukcja Użytkownika
Waters High Performance Carbohydrate Column User Manual,
4 strony
|
| DisQuE Dispersive Sample Preparation Kit |
Instrukcja Użytkownika
Waters DisQuE Dispersive Sample Preparation Kit User Manual,
5 strony
|
| Protein Separation Technology ACQUITY UPLC BEH300, |
Instrukcja Użytkownika
Waters Protein Separation Technology ACQUITY UPLC BEH300, C4, 1.7 µm Columns User Manual,
11 strony
|
| Gen-Pak FAX Columns |
Instrukcja Użytkownika
Waters Gen-Pak FAX Columns User Manual,
7 strony
|
| Oasis Prospekt-2/Symbiosis Cartridges |
Instrukcja Użytkownika
Waters Oasis Prospekt-2/Symbiosis Cartridges User Manual,
4 strony
|
| Symmetry Columns |
Instrukcja Użytkownika
Waters Symmetry Columns User Manual,
10 strony
|
| Spherisorb Columns |
Instrukcja Użytkownika
Waters Spherisorb Columns User Manual,
11 strony
|
| PoraPak RXN Cartridges |
Instrukcja Użytkownika
Waters PoraPak RXN Cartridges User Manual,
5 strony
|
| Sentry Guard Column |
Instrukcja Użytkownika
Waters Sentry Guard Column User Manual,
4 strony
|
| MassPREP E. coli Digestion Standard |
Instrukcja Użytkownika
Waters MassPREP E. coli Digestion Standard User Manual,
3 strony
|
| UPLC Intact Mass Analysis Application Kit |
Instrukcja Użytkownika
Waters UPLC Intact Mass Analysis Application Kit User Manual,
8 strony
|
| Oasis Glass Cartridges |
Instrukcja Użytkownika
Waters Oasis Glass Cartridges User Manual,
3 strony
|
| Certified Sep-Pak |
Instrukcja Użytkownika
Waters Certified Sep-Pak User Manual,
6 strony
|
| Sep-Pak DNPH-Silica Cartridges |
Instrukcja Użytkownika
Waters Sep-Pak DNPH-Silica Cartridges User Manual,
11 strony
|
| ACQUITY UPLC BEH Glycan, 1.7 µm Columns, Glycan Pe |
Instrukcja Użytkownika
Waters ACQUITY UPLC BEH Glycan, 1.7 µm Columns, Glycan Performance Test Standard User Manual,
9 strony
|
| BioSuite Peptide Analysis Columns |
Instrukcja Użytkownika
Waters BioSuite Peptide Analysis Columns User Manual,
8 strony
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Perfect..